Groundwork Chico ConcreteGroundwork Chico Concrete

Concrete cutting in Chico CA - clean cuts planned around what's inside the slab

Need an opening, a trench or a section of slab removed? We scan first, cut clean and leave your property cleaned up.

Covered brick patio with a concrete floor, stone outdoor kitchen counter, and cushioned seating beneath a wood ceiling.

I measure every job myself

I come out to look at each job, measure the cut and ask what the opening is for. Our crew of finishers and laborers then does the work, so you deal with the same small team from the first visit to the cleanup.

In business since 2013

We've been forming, pouring and cutting concrete for 13 years. I spent my early years writing quotes and walking jobs, then learned finishing from people I'd worked beside, so what I write down is what our crew builds.

Licensed and fully insured

We're licensed and fully insured, which matters on a job where a saw runs close to wiring and steel. Every job is backed by our satisfaction guarantee. When you're ready, call (530) 399-1528 or send us the form.

Concrete cutting in Chico, planned first

Concrete cutting is how we make trenches, openings and clean edges in concrete, using diamond saws and core bits that drill round holes through floors, driveways and walls. Groundwork Chico Concrete does it for Chico homeowners and property owners who need part of a slab out without breaking up the rest.

Most cutting calls start with concrete that's in the way of something else. It might be a trench across a garage floor for a new drain line, a cracked driveway panel that has to come out, a doorway through a concrete wall or a straight edge where an old patio meets new work. What we're cutting, how thick it is and whether a saw can reach it decide which saw we bring and how the day is set up.

The price comes down to how long and how deep the cut is, whether the slab has steel in it and whether it's a floor or a wall, since wall sawing usually costs more. On a short cut, the cost of bringing the crew and saw out can outweigh the footage itself. The schedule turns on the scan, any permit the job needs and room for the saw, and your estimate lays out each step.

Concrete cutting, scanning and slurry cleanup

Scanning the slab before we cut

Before the first cut, we have the slab scanned so we know what's inside it. The scan uses ground-penetrating radar, GPR for short, to find rebar, the steel bars that hold a slab together, along with post-tension cables and live electrical conduit. Cutting a tensioned cable or a live line can be deadly, so the saw doesn't start until we've marked around what the scan found.

Flat saw or wall saw

Most cuts around a house are flat sawing, which handles level surfaces like floors, driveways, sidewalks and trenches for a new line. A wall, a column or an opening where a floor saw can't work calls for a wall saw mounted on a track. Plenty of our flat sawing feeds other work, like cutting out a broken section ahead of a new concrete driveway or squaring an edge so patio construction can tie into the old slab.

Keeping dust and slurry contained

Concrete dust carries crystalline silica, and water on the blade cuts that dust way down, so most sawing runs wet. Wet cutting leaves slurry, the gray mix of water and cuttings, which has to be vacuumed up or contained instead of left to drain away. We plan how the water and slurry get collected before we start, so your property stays clean. Dry cutting still has a place with small hand saws where water isn't practical, and then the blade and a vacuum handle the dust.

Get a written estimate for your concrete cut

We reply within one business day, then I come out to measure, take photos and write up a free estimate with no obligation. It helps to tell us the surface, where it is and roughly how long the cut runs.

(530) 399-1528

How a concrete cutting job goes

  1. I come out and measure

    After you call, I come out to measure, take photos and ask what the cut is for. We then send a written estimate that lists each step, from the scan to the cleanup, so you know what's included before anything starts.

  2. Permits and a date

    If a permit is part of the job, we find out which city or county office handles your address before we set a date. For work on a city sidewalk or street, Chico aims to review a complete application within 10 business days.

  3. Cutting, cleanup and walkthrough

    Our crew sets up the saw, cuts along the marked lines and collects the slurry as it goes. If digging follows the cut, we allow at least 2 working days after contacting USA North 811. Then I walk the work with you against the estimate.

Concrete cutting questions from Chico

How much does concrete cutting cost in Chico?

Saw cutting an accessible concrete slab usually costs about $4 to $10 per linear foot across the US. That's the national market range for straightforward slab cuts, not our price. For your job, I measure the cut on site and the written estimate gives your price step by step.

Do I need a permit to cut concrete in Chico?

If the cut alters part of a building, plan on one, because Chico requires a building permit to alter or demolish any building or structure, and its exemption list names low walks and driveways but not cutting. A cut that reaches a city sidewalk or street falls under the city's encroachment rules. When a permit is needed, we take care of the application and inspections with you.

Who is allowed to do concrete cutting in California?

Concrete cutting is licensed contractor work in California, and the state's concrete related services class covers sawing, breaking and coring. Chico's online permit system asks a first-time contractor for that state license number and a city business license number. The exception is small work under $1,000, up from $500, that needs no permit and uses no hired help.

Can you cut a door opening in a concrete wall?

Usually, once the structural engineer of record, the engineer behind your building's design, has planned the opening. The usual guidance for this work is that any structural opening, or any cut through structural steel, needs that engineer before cutting starts. Mention the opening when I come out, so we can line up the engineer's plan before we set a date.